 |
DRL Relay Harness (Item #: HDRL) - Used on vehicles that decreases voltage below 10V or reverses polarity for DRLs. Also can be used on older vehicles to provide better current to the HID conversion kit. This harness is NOT a standard relay harness. Standard relays fail to function properly at voltages under 10V, while the relays used in this harness can be triggered by voltages as low as 3V. |
 |
Single Beam All In One Harness (Item #: HAI1) - Used for vehicles with light out sensors & DRLs. Is a combination of everything to make even the toughest single beam applications work. Usefull for BMW, Mercedes, Dodge, Ford, Audi, etc. Will overcome low voltage issues, resistance sensing issues, light out indicators, etc. |
 |
Ballast Extension Wire (Item #: WE100, WE150) - For motorcycles that must have ballasts mounted under seat. Not recommended for cars and trucks, as the life of the ballast and bulb will be shortened. |
 |
Capacitor & Inductor Box (Item #: CAP2) - Helps to reduce radio intereference. Also used on vehicles that have slight gaps of power when switch from high to low beams. This product has polarity and MUST be installed properly. If installed improperly, the product will explode and may injure those around it.
|
 |
Resistor Box (Item #: RES2) - Used on vehicles that have light out warning indicators. This module tricks the vehicles' computer into thinking that a regular light bulb is installed, and in turn, shuts off the light out indicator. Please note that once this device is installed, the light out indicator will never turn on again while the device is functioning properly. Also, this module becomes extremely hot when used - install appropriately. |
 |
Resistor Box (Item #: RES3) - Used on vehicles that have light out warning indicators. This module tricks the vehicles' computer into thinking that a regular light bulb is installed, and in turn, shuts off the light out indicator. Please note that once this device is installed, the light out indicator will never turn on again while the device is functioning properly. Also, this module becomes extremely hot when used - install appropriately. |
 |
Ceramic Resistors (Item# RESC2, RESC4, RESC6, RESC8) - Used on vehicles that have light out warning indicators. These resistors tricks the vehicles' computer into thinking that a regular light bulb is installed, and in turn, shuts off the light out indicator. Please note that once this device is installed, the light out indicator will never turn on again while the device is functioning properly. These resistors become extremely hot when used - install appropriately. We offer these resistors in 3 different OHM ratings: 2, 4, 6, and 8 ohm. |
 |
90047 High / Low Harnesses (Item #: H90047) - For use with 9004 or 9007 HID conversion kits. Can be used with single beam kits to provide constant
voltage to ballasts when in vehicle is in daytime running light mode, and also prevent lights from completely shutting off when switching to the high beam setting. |
 |
H4 High / Low Harnesses (Item#: HH4) -
For use with H4 HID conversion kits. Can be used with single beam kits to provide constant
voltage to ballasts when in vehicle is in daytime running light mode, and also prevent lights from completely shutting off when switching to the high beam setting. |
 |
H13 high / low harnesses (Item #: HH13) -
For use with H13 HID conversion kits. Can be used with single beam kits to provide constant
voltage to ballasts when in vehicle is in daytime running light mode, and also prevent lights from completely shutting off when switching to the high beam setting. |
 |
9007 Connector Terminator (Item #: T9007) - Used in conjunction with 9007 Bi-Xenon Hi/Lo Kits to complete the circuitry on the empty vehicle socket. Can help to restore DRL functionality caused by empty socket not used by Bi-Xenon kits. |
 |
9007 Female Connector To 2 Male 9006 Connectors (Item #: C9007) - Used in conjunction with RES2 resistors. Eliminates the need to cut and splice RES2 into factory socket. |
 |
H4 Connector Terminator (Item #: TH4) - Used in conjunction with H4 Bi-Xenon Hi/Lo Kits to complete the circuitry on the empty vehicle socket. Can help to restore DRL functionality caused by empty socket not used by Bi-Xenon kits. |
 |
H4 Female Connector To 2 Male 9006 Connectors (Item #: CH4) - Used in conjunction with RES2 resistors. Eliminates the need to cut and splice RES2 into factory socket. |
 |
H13 Connector Terminator (Item #: TH13) - Used in conjunction with H13 Bi-Xenon Hi/Lo Kits to complete the circuitry on the empty vehicle socket. Can help to restore DRL functionality caused by empty socket not used by Bi-Xenon kits. |
 |
H13 Female Connector To 2 Male 9006 Connectors (Item #: CH13) - Used in conjunction with RES2 resistors. Eliminates the need to cut and splice RES2 into factory socket. |
